Strength of Materials Basics: Stress, Strain, Bending, Torsion and Buckling with Worked Examples

Strength of materials answers a very practical question: will this part carry the load without breaking, bending too much or buckling? Whether you are studying mechanical or civil engineering, building a workshop frame or just curious why a ruler snaps when you press it on its flat side but resists when held on edge, the same handful of formulas explain what happens.

This guide covers the essentials with worked numbers: stress and strain, Hooke’s law, factor of safety, bending, deflection, torsion, buckling and thermal stress. The examples use round values so you can follow each step. Real structures must be designed by qualified engineers using the applicable codes; treat this as learning material, not a design tool.

Stress and strain

Stress is force per unit area: σ = F ÷ A. In SI units force is in newtons and area in square metres, giving pascals; engineers usually work in megapascals (1 MPa = 1 N/mm²). Strain is the fractional change in length: ε = ΔL ÷ L, which has no units.

Within the elastic range, stress and strain are proportional, and the constant is Young’s modulus E: σ = E × ε (Hooke’s law). Typical values are about 200 GPa for steel, 70 GPa for aluminium and 10 GPa or so for timber along the grain. A higher E means a stiffer material, which is different from being stronger. Strength is about how much stress a material can take before yielding or breaking.

QuantityFormulaTypical units
Axial stressσ = F ÷ AMPa (N/mm²)
Strainε = ΔL ÷ Ldimensionless
Hooke’s lawσ = E εMPa, GPa for E
Axial elongationδ = F L ÷ (A E)mm
Shear stress (direct)τ = V ÷ AMPa

Worked example 1: a steel rod in tension

A steel rod of 20 mm diameter and 2 m length carries a pull of 50 kN. Assume E = 200 GPa and a yield strength of 250 MPa.

  • Area: A = π × 20² ÷ 4 = 314.2 mm².
  • Stress: σ = 50,000 N ÷ 314.2 mm² ≈ 159 MPa.
  • Strain: ε = 159 ÷ 200,000 ≈ 0.0008, which is 0.08%.
  • Elongation: δ = ε × L = 0.000796 × 2,000 mm ≈ 1.6 mm.
  • Factor of safety against yield: 250 ÷ 159 ≈ 1.57.

The rod stretches by only 1.6 mm and stays elastic. A factor of safety of 1.57 may be fine for a controlled test but is low for a structure where loads are uncertain; codes commonly require larger factors depending on the application.

Factor of safety

The factor of safety (FoS) is the ratio of the strength of the material to the stress in use: FoS = failure stress ÷ working stress. It covers uncertainty in loads, material variation, manufacturing defects and ageing. Ductile metals are usually compared against yield strength, brittle materials such as cast iron and concrete against ultimate strength. Higher uncertainty or higher consequences of failure call for higher factors. Lifting equipment, pressure vessels and building structures all have codes that specify them.

Bending of beams

When a beam carries a load across a span, it bends. The top fibres are compressed and the bottom ones stretched (for a simply supported beam with a downward load), with the neutral axis between them carrying no bending stress. The bending stress is σ = M × y ÷ I, where M is the bending moment, y is the distance from the neutral axis and I is the second moment of area of the cross-section. For a rectangle of width b and depth h, I = b h³ ÷ 12.

For a simply supported beam of span L with a point load P at the centre, the maximum moment is M = P L ÷ 4 and the maximum deflection is δ = P L³ ÷ (48 E I).

Worked example 2: a steel flat as a beam

A steel bar 50 mm wide and 100 mm deep spans 2 m between simple supports and carries a 5 kN load at the middle. E = 200 GPa.

  • Second moment of area: I = 50 × 100³ ÷ 12 = 4.167 × 10⁶ mm⁴.
  • Maximum moment: M = 5,000 × 2 ÷ 4 = 2,500 N·m = 2.5 × 10⁶ N·mm.
  • Maximum bending stress: σ = M y ÷ I = 2.5 × 10⁶ × 50 ÷ 4.167 × 10⁶ = 30 MPa.
  • Maximum deflection: δ = 5,000 × 2,000³ ÷ (48 × 200,000 × 4.167 × 10⁶) = 1.0 mm.

Now turn the bar so it is 100 mm wide and 50 mm deep. I becomes 100 × 50³ ÷ 12 = 1.04 × 10⁶ mm⁴, four times smaller. The stress rises to 60 MPa and the deflection to about 4 mm. Same material, same weight, four times the deflection. Depth is cubed in the second moment of area, which is why floor joists are placed on edge and why I-beams put material far from the neutral axis.

Torsion of shafts

A shaft transmitting torque T develops shear stress that is zero at the centre and highest at the outer surface: τ = T × r ÷ J, where r is the radius and J is the polar second moment of area. For a solid circular shaft of diameter d, J = π d⁴ ÷ 32. The angle of twist over a length L is θ = T L ÷ (G J), where G is the shear modulus (about 80 GPa for steel).

Worked example 3. A solid steel shaft of 30 mm diameter transmits 200 N·m. J = π × 30⁴ ÷ 32 = 79,520 mm⁴. The surface shear stress is τ = 200,000 N·mm × 15 mm ÷ 79,520 mm⁴ ≈ 37.7 MPa. Doubling the diameter would reduce the stress by a factor of eight, since J scales with d⁴ and r with d. The link between power and torque is P = T × ω, so a motor delivering 2 kW at 1,000 rpm (about 104.7 rad/s) gives T ≈ 19 N·m.

Buckling of slender columns

A short, thick column fails by crushing when the stress reaches the material’s compressive strength. A long, slender column fails far earlier by buckling, which is a sudden sideways bowing. Euler’s formula gives the critical load: Pcr = π² E I ÷ (K L)², where K is an effective-length factor depending on the end conditions: 1.0 for pinned ends, 0.5 for fixed ends, 2.0 for a free-standing cantilever column, and about 0.7 for one fixed and one pinned end.

Worked example 4. Take the same 20 mm steel rod, now used as a 2 m column pinned at both ends. I = π d⁴ ÷ 64 = 7,854 mm⁴. Pcr = π² × 200,000 × 7,854 ÷ 2,000² ≈ 3,876 N, or only about 3.9 kN. Compare that with the crushing load: 250 MPa × 314 mm² ≈ 78.5 kN. The rod buckles at about one twentieth of the load it could carry in tension or short compression. Slenderness, not material strength, governs. That is why long compression members use tubes, angles and braced frames: they increase I without adding much weight.

Thermal stress

Materials expand when heated by ΔL = α × L × ΔT. If expansion is prevented, stress develops: σ = E × α × ΔT. For steel, α ≈ 12 × 10⁻⁶ per kelvin. A fully restrained steel bar heated by 40 K develops σ = 200,000 × 12 × 10⁻⁶ × 40 = 96 MPa, a large stress from a modest temperature rise. Railways, pipelines and bridges therefore need expansion joints or other provisions. A 12 m steel rail free to expand lengthens by 12 × 10⁻⁶ × 12,000 mm × 40 ≈ 5.8 mm over the same 40 K rise.

How to approach any strength problem

  1. Draw the part and the loads, and find reactions by equilibrium.
  2. Identify the type of loading: axial, bending, shear, torsion, or a combination.
  3. Find the critical section, where moment or load is largest or where the area is smallest.
  4. Calculate stress and compare with the allowable value for the material.
  5. Check deflection, because stiffness often governs before strength does.
  6. For compression members, check buckling.
  7. Check units and sanity: does the answer have the right magnitude?

Common mistakes

  • Mixing mm with m or N with kN. Work consistently in N and mm to get MPa directly.
  • Using the wrong axis for I, or forgetting that depth is cubed.
  • Treating strong as stiff. Strength and modulus are different properties.
  • Skipping the buckling check on slender compression members.
  • Ignoring stress concentrations at holes, notches and sharp corners.
  • Forgetting the self-weight of the member or dynamic effects.

Unit slips cause most lost marks, and our guide to unit conversions and dimensional analysis shows a reliable way to check them. For related topics, see thermodynamics and heat transfer, basic circuit calculations and choosing the right statistical test for analysing test data. The free Free Technology Calculators app helps with quick conversions, and its guide lists what it covers. Engineering students may also like free calculators for engineering students and the products page.

Frequently asked questions

What is the difference between stress and pressure?

Both are force per area and share units. Pressure usually describes a fluid pushing on a surface; stress is the internal force intensity inside a solid.

What are yield strength and ultimate strength?

Yield strength is where permanent deformation starts. Ultimate strength is the maximum stress the material reaches before fracturing. Designs normally keep stresses below yield.

Why do beams have an I-shaped section?

Bending stress is highest at the top and bottom edges, so putting most material in the flanges gives a large I for little weight, while a thin web connects them and carries shear.

Can I use these formulas to design a real structure?

They are the foundation, but real designs need code-based loads, load combinations, connections, fatigue and professional review.

Disclaimer: This article is for education. Material properties vary by grade and source; use values from standards or datasheets. Do not use these simplified examples to design or certify load-bearing structures or safety-critical parts without a qualified engineer.

Leave a Reply

Share Your Love